manualshive.com logo in svg

Siemens 7ME6810, Operating Instructions Manual, Page: 4 / 170

Share
Download
Siemens 7ME6810 Operating Instructions Manual Download Page 4

4.7.2

Installation conditions.............................................................................................................32

4.7.2.1

MID option (MI-001) ...............................................................................................................32

5

Connecting .................................................................................................................................................33
5.1

General safety requirements..................................................................................................34

5.2

Remote version ......................................................................................................................35

5.3

Power supply..........................................................................................................................36

5.4

Outputs...................................................................................................................................38

5.5

Communication modules........................................................................................................39

5.6

Connection of add-on modules ..............................................................................................42

6

Commissioning ...........................................................................................................................................43
6.1

Overview SIMATIC PDM........................................................................................................43

6.2

Initial commissioning via SIMATIC PDM................................................................................44

6.2.1

Check SIMATIC PDM version................................................................................................44

6.2.2

Updating the Electronic Device Description (EDD) ................................................................44

6.2.3

Configuring the device ...........................................................................................................46

6.3

Setting the basic parameters .................................................................................................51

6.4

Unit selection..........................................................................................................................56

6.5

Output configuration...............................................................................................................56

6.6

Data protection.......................................................................................................................58

7

Operating....................................................................................................................................................59
7.1

Operation via key and display ................................................................................................59

7.2

Display symbols .....................................................................................................................60

7.3

Default display information and accessible display menus ....................................................61

7.4

Operator menu .......................................................................................................................64

7.5

Internal data handling.............................................................................................................70

7.6

Battery-powered operation.....................................................................................................71

8

Service and maintenance ...........................................................................................................................77
8.1

Maintenance...........................................................................................................................77

8.2

MAG 8000 service guidelines ................................................................................................77

8.3

Replacing transmitter or PCB board ......................................................................................78

8.4

Battery replacement ...............................................................................................................79

8.5

Power up with battery reset, date and time set up .................................................................81

8.6

Verification mode ...................................................................................................................82

8.7

Transport................................................................................................................................83

8.8

Return procedure ...................................................................................................................83

8.9

Disposal .................................................................................................................................84

8.9.1

Battery disposal......................................................................................................................85

Table of contents

SITRANS FM MAG 8000

4

Operating Instructions, 03/2020, A5E03071515-AH

Summary of Contents for 7ME6810











































































































































































Reviews:

No comments