Siemens 7ME6810 Operating Instructions Manual Download Page 59 | Manualshive

Page: 59 / 170

Siemens 7ME6810 Operating Instructions Manual Download Page 59

Operating

7

7.1

Operation via key and display

The meter is designed with a single key and a symbolic display for optimal dialog.

Display

Display is divided into 3 areas.

6WDWXV

,QIRUPDWLRQ

,QGH[ PHQX

Figure 7-1

Display

● Top area with symbols for status information.
● Middle area with actual information.
● Bottom area with index for actual information and selected menu.
Some of the information has additional information connected and display will automatically

toggle between information, see menu overview (Page 64). If key is not pressed for 10

minutes, display will time-out and return to default configured operator menu.

Key

There are three different ways the interface key will respond to being pressed:
1. A brief press (less than 2 seconds) will advance screen to next index or menu.
2. A short press (2 to 5 seconds) will enter a menu or escape menu selection.
3. A long press (more than 5 seconds) while in the operator menu ( ) will activate a reset of

selected value (e.g., call-up function) indicated by an "r".

A flashing "r" indicates a reset. A request for time and date setup is shown during power-up.

SITRANS FM MAG 8000

Operating Instructions, 03/2020, A5E03071515-AH

59

«
...
57
58
59
60
61
...
»

Summary of Contents for 7ME6810











































































































































































Reviews:

No comments