manualshive.com logo in svg

Siemens 7ME6810, Operating Instructions Manual, Page: 94 / 170

Share
Download
Siemens 7ME6810 Operating Instructions Manual Download Page 94

Meter

MAG 8000 Standard

(7ME6810)

MAG 8000 CT

(7ME6820)

 

Custody transfer approval

NMI

OIML R49:2013

OIML R 49 MAA

MI-001 (DK-0200-MI001-011)

NMI

Conformity

 

-

CEN EN 14154

ISO 4064

PED

2014/68/EU

EMC

EN 61326-1

For further features, see "Features" (Page 163).

10.2

Sensor

Technical specifications

Sensor

MAG 8000

(7ME6810)

MAG 8000 CT

(7ME6820)

Size, flange and pressure 

range

EN 1092-1

(DIN 2501)

DN 25, DN 40, DN 350 - DN 600: PN 

40

DN 50 to 150: PN 16

DN 200 to 1200: PN 10 or PN 16

DN 350 - DN 600: PN 25

DN 50 to 600: PN 16

ANSI 16.5

Class 150 lb

1" to 24": 20 bar (290 psi)

2" to 24": 16 bar (232 psi)

AWWA C-207

28" to 48": PN 10

-

AS 4087

DN 50 to 1200: PN 14

DN 50 to 600: PN 16

AS 2091-1

Table D

-

-

AS 2191

Table E

 

 

Max. excitation frequency

Basic version

Battery-pow‐

ered

1/15 Hz for sensor size 

DN 25 to 150 (1" to 6")

1/30 Hz for sensor size 

DN 200 to 600 (8" to 24")

1/60 Hz for sensor size 

DN 700 to 1200 (28" to 48")

1/15 Hz for sensor size 

DN 50 to 150 (1" to 6")

1/30 Hz for sensor size 

DN 200 to 600 (9" to 24")

Mains-powered

6.25 Hz for sensor size 

DN 25 to 150 (1" to 6")

3.125 Hz for sensor size 

DN 200 to 600 (8" to 24")

1.5625 Hz for sensor size 

DN 700 to 1200 (28" to 48")

6.25 Hz for sensor size 

DN 25 to 150 (1" to 6")

3.125 Hz for sensor size 

DN 200 to 600 (8" to 24")

Technical data
10.2 Sensor

SITRANS FM MAG 8000

94

Operating Instructions, 03/2020, A5E03071515-AH

Summary of Contents for 7ME6810











































































































































































Reviews:

No comments