manualshive.com logo in svg

Siemens 7ME6810, Operating Instructions Manual, Page: 80 / 170

Share
Download
Siemens 7ME6810 Operating Instructions Manual Download Page 80

7. Place and secure new battery pack.

Note
Battery packs must be installed with the top part in upwards direction to reach maximum 

capacity.

8. Add new Silica gel bag

– Remove plastic bag from new silica gel bag.
– Place new silica gel bag on top of battery pack to prevent condensation within meter.
– To maintain IP68 enclosure the silica gel bag may not be in contact with the Sylgard.

9. Disconnect old battery pack and connect new one.
10.Press key within 6 seconds to reset battery (i.e. operating time and remaining capacity) 

when display shows:

11.Mount top lid.
12.Fasten screws to reassemble meter completely.

If necessary, adjust time and date via software, see "Power up with battery reset, date and time 

set up".

Note
Re-verification
All sealed MAG 8000 CT meters must be re-verified when sealings (marked "A") have been 

broken. The re-verification must be performed by an authorized person, with the acceptance 

and under direction of the local authorities.

Service and maintenance
8.4 Battery replacement

SITRANS FM MAG 8000

80

Operating Instructions, 03/2020, A5E03071515-AH

Summary of Contents for 7ME6810











































































































































































Reviews:

No comments