manualshive.com logo in svg

Siemens 7ME6810, Operating Instructions Manual, Page: 97 / 170

Share
Download
Siemens 7ME6810 Operating Instructions Manual Download Page 97

Power supply
12-24 V AC/DC power supply

Input voltage range

12/24 V AC/DC (10 ... 32 V DC)

Power consumption

2 VA

Isolation

Class II

Fuse

1000 mA T - Not replaceable

Short circuit protection

Module is protected from short circuit on the output con‐

nector. Both during mains and backup supply

Conformity

IEC 61010-1

OIML R49:2013

EMC: EN 61326-1

115 to 230 V AC mains supply Input voltage range

115 to 230 V AC, +15% to −20%, 50-60 Hz

Power consumption

2 VA

Isolation

Class II

Fuse

250 mA T - Not replaceable

Short circuit protection

Module is protected from short circuit on the output con‐

nector. Both during mains and backup supply

Conformity

IEC 61010-1

OIML R49

EMC:

EN 61326-1

Input cable for 

12/24 V AC/DC and 

115 to 230 V AC power supply

Factory-mounted PUR cable

2 x 1 mm

2

 (brown, blue)

Length = 3 m

Resistance

Sunlight and water

Outer diameter

7 mm (0.28")

Rated voltage

300 ... 500 V AC

Testing voltage

2000 V AC

Temperature range

Fixed laying: 

Flexible application: 

−40 to +90 °C (-40 to 194 °F)

−30 to +80 °C (-22 to 176 °F)

Bending radius

Min. 28 mm (fixed installation)

Pulling force

Max. 200 N

Output

Female connector

Backup battery

Male connector

1)

 Lithium batteries are subject to special transportation regulations according to United Nations 

"Regulation of Dangerous Goods, UN 3090 and UN 3091". Special transport documentation is 

required to observe these regulations. This may influence both transport time and costs.

10.5

Modbus RTU

Siemens Flow Instruments Modbus RTU specification for add-on modules
Device type

Slave

Baud rates

1200, 2400, 4800, 9600, 19 200, 38 400 bits/sec.

Number of stations

Recommended: max. 31 per segment without repeaters for RS 485

Device address range

1 to 247

Technical data

10.5 Modbus RTU

SITRANS FM MAG 8000

Operating Instructions, 03/2020, A5E03071515-AH

97

Summary of Contents for 7ME6810











































































































































































Reviews:

No comments