manualshive.com logo in svg

Siemens 7ME6810, Operating Instructions Manual, Page: 19 / 170

Share
Download
Siemens 7ME6810 Operating Instructions Manual Download Page 19

MAG 8000 CT is approved with OIML R49:2013 and MID for the following installations:
● DN 50 to DN 300 with 0x D

i

 of straight pipe upstream to the sensor and 0x D

i

 of straight pipe 

downstream from the sensor.

● DN 350 to DN 600 with 3x D

i

 of straight pipe upstream to the sensor and 3x D

i

 of straight pipe 

downstream from the sensor.

For optimal measurement performance, it is recommended to follow the installation guidelines 

for the MAG 8000 standard water meter.

 

 

MAG 8000
(recommended)

MAG 8000 CT
DN 50 to DN 300

MAG 8000 CT
DN 350 to DN 600

①

Minimum straight inlet pipe length

5x D

i

0x D

i

3x D

i

②

Minimum straight outlet pipe length

3x D

i

0x D

i

3x D

i

Sensor must be completely full of liquid

Installing/Mounting

4.1 Sensor installation

SITRANS FM MAG 8000

Operating Instructions, 03/2020, A5E03071515-AH

19

Summary of Contents for 7ME6810











































































































































































Reviews:

No comments