Siemens 7ME6810 Operating Instructions Manual Download Page 3

Page: 3 / 170

Table of contents

Introduction...................................................................................................................................................7
1.1

Purpose of this documentation.................................................................................................7

1.2

Items supplied ..........................................................................................................................7

1.3

Document history .....................................................................................................................8

1.4

Checking the consignment.......................................................................................................8

1.5

Security information .................................................................................................................8

1.6

Transportation and storage ......................................................................................................9

1.7

Notes on warranty ....................................................................................................................9

Safety notes................................................................................................................................................11
2.1

General safety instructions.....................................................................................................11

2.2

Laws and directives................................................................................................................11

2.3

Conformity with European directives......................................................................................11

2.4

Lithium batteries.....................................................................................................................12

2.5

Installation in hazardous area ................................................................................................12

Description..................................................................................................................................................13
3.1

System components...............................................................................................................13

3.2

Operating principle .................................................................................................................13

3.3

Design ....................................................................................................................................13

3.4

Benefits ..................................................................................................................................15

Installing/Mounting......................................................................................................................................17
4.1

Sensor installation..................................................................................................................18

4.1.1

Locating the sensor................................................................................................................18

4.1.2

Orienting the sensor...............................................................................................................20

4.1.3

Mounting the sensor...............................................................................................................22

4.2

Potential equalization .............................................................................................................25

4.3

Grounding ..............................................................................................................................26

4.4

Cathodic-protected pipes .......................................................................................................28

4.5

Potting and direct burial .........................................................................................................28

4.6

Transmitter installation ...........................................................................................................29

4.7

MAG 8000 CT ........................................................................................................................30

4.7.1

Sealing of MAG 8000 CT .......................................................................................................31

4.7.1.1

Verification sealing .................................................................................................................31

4.7.1.2

User sealing ...........................................................................................................................31

SITRANS FM MAG 8000

Operating Instructions, 03/2020, A5E03071515-AH

Summary of Contents for 7ME6810











































































































































































Search results

Summary of Contents for 7ME6810

Reviews:

Siemens 7ME6810, Operating Instructions Manual, Page: 3 / 170

Search results

Summary of Contents for 7ME6810

Reviews: