Siemens 7ME6810 Operating Instructions Manual Download Page 120

Page: 120 / 170

Connecting PC to meter

Connect IrDa communication adaptor to its interface on transmitter and connect PC to adaptor.

Figure C-1

MAG 8000 or MAG 8000 CT has a built-in IrDA communication interface on top of meter.
IrDA adaptor can be fixed to lid by rubber band.

Starting Flow Tool software program

Double-click on Flow Tool icon on windows desktop to start program.

Note
For on-line communication make sure the IrDA symbol is visible in the toolbar status menu

before starting Flow Tool.

C.3

Configuring the device

This chapter describes how to set up meter for communication with PC. The options in both

Flow Tool and SIMATIC PDM software are the same; only the views on the PC screen differ.

Flow Tool
C.3 Configuring the device

SITRANS FM MAG 8000

120

Operating Instructions, 03/2020, A5E03071515-AH

Summary of Contents for 7ME6810











































































































































































Search results

Summary of Contents for 7ME6810

Reviews:

Siemens 7ME6810, Operating Instructions Manual, Page: 120 / 170

Search results

Summary of Contents for 7ME6810

Reviews: