manualshive.com logo in svg

Siemens 7ME6810, Operating Instructions Manual, Page: 21 / 170

Share
Download
Siemens 7ME6810 Operating Instructions Manual Download Page 21

Sensor must be mounted as shown in upper part of figure. Do not mount sensor as shown in 

lower part of figure as electrodes then will be positioned at top where air bubbles may occur and 

in bottom, where mud, sludge, sand etc. may deposit and cover the electrode, thus impacting 

the measurement.
If "Empty Pipe Detection" is used, sensor should be tilted 45° as shown in upper right figure to 

maximize full pipe detection and provide accurate volume calculations.

Note
Physical installation of battery pack may influence battery capacity. Optimal battery capacity is 

achieved with battery pack in an upright position. Installation examples marked with dotted 

cross will affect battery capacity.

Vertical pipes (MAG 8000)

Recommended installation is in a vertical/inclined pipe to minimize wear and deposits in sensor.

Installation in large pipes (MAG 8000)

The water meter can be installed between two reducers (e.g. DIN 28545).

With an 8° reducer, the following pressure drop curve applies. The curves are applicable to 

water.

Installing/Mounting

4.1 Sensor installation

SITRANS FM MAG 8000

Operating Instructions, 03/2020, A5E03071515-AH

21

Summary of Contents for 7ME6810











































































































































































Reviews:

No comments