manualshive.com logo in svg

Siemens 7ME6810, Operating Instructions Manual, Page: 11 / 170

Share
Download
Siemens 7ME6810 Operating Instructions Manual Download Page 11

Safety notes

2

2.1

General safety instructions

CAUTION

Correct, reliable operation of the product requires proper transport, storage, positioning and 

assembly as well as careful operation and maintenance.
Only qualified personnel should install or operate this instrument.  

Note
Alterations to the product, including opening or improper modifications of the product are not 

permitted.
If this requirement is not observed, the CE mark and the manufacturer's warranty will expire.

2.2

Laws and directives

Observe the safety rules, provisions and laws applicable in your country during connection, 

assembly and operation. These include, for example:     
● National Electrical Code (NEC - NFPA 70) (USA)
● Canadian Electrical Code (CEC) (Canada)
Further provisions for hazardous area applications are for example:   
● IEC 60079-14 (international)
● EN 60079-14 (EU)

2.3

Conformity with European directives

The CE marking on the device symbolizes the conformity with the following European 

directives:

Electromagnetic compatibili‐

ty EMC 

2014/30/EU

Directive of the European Parliament and of the Council on the 

harmonisation of the laws of the Member States relating to elec‐

tromagnetic compatibility

Low voltage directive LVD 

2014/35/EU

Directive of the European Parliament and of the Council on the 

harmonisation of the laws of the Member States relating to the 

making available on the market of electrical equipment designed 

for use within certain voltage limits

SITRANS FM MAG 8000

Operating Instructions, 03/2020, A5E03071515-AH

11

Summary of Contents for 7ME6810











































































































































































Reviews:

No comments