manualshive.com logo in svg

Siemens 7ME6810, Operating Instructions Manual, Page: 42 / 170

Share
Download
Siemens 7ME6810 Operating Instructions Manual Download Page 42

5.6

Connection of add-on modules

When the add-on module has been installed, the electrical connections are available on 

terminal rows 91-97.  

For more information

Refer to the relevant BUS communication Quick Start or Operating Instructions available on an 

included DVD or on the internet, at: www.siemens.com/flowdocumentation 

(

www.siemens.com/flowdocumentation

).

Information on the operation of communication modules

For information on how to operate the various communication modules, see:
● 3G/UMTS add-on module Operating Instructions (

https://support.industry.siemens.com/cs/

ww/en/view/109751612

)

● Modbus RTU Operating Instructions (

http://support.automation.siemens.com/WW/view/en/

54091509

)

Connecting
5.6 Connection of add-on modules

SITRANS FM MAG 8000

42

Operating Instructions, 03/2020, A5E03071515-AH

Summary of Contents for 7ME6810











































































































































































Reviews:

No comments