Sharp AR-650, Service Handbook

Page: 24 / 200

1 - 17 ADJUSTMENT
05 MODE
CODE ADJUSMENT MODE DEFAULT RANGE DESCRIPTION
PROCEDURE
GROUP
410 Laser write position(front to rear of machine Copier 140 0-255 1
image registration).
After adjusting code 411, key in the value set
in code 411, press the SET key to store in
memory or the CLEAR key to reset.
♥
411 Laser write position (front to rear of machine Printer 140 0-255 1
image registration).
♥
415 First beam laser power. Copier 103 0-255 1
♥
416 First beam laser power. Printer 103 0-255 1
♥
430 Copy leading edge void adjustment. Copier 24 0-255 1
♥
431 Copy top edge void adjustment (rear of Copier 0 0-255 1
machine). Top of copy LT/A4 or right side edge
of ST-R/A5-R, LT-R/A4-R, Legal/B4 and
Ledger/A3.
♥
432 Copy bottom edge void adjustment (front of Copier 0 0-255 1
Machine). Bottom of copy LT/A4 or left side
edge of ST-R/A5-R, LT-R/A4-R, Legal/B4 and
Ledger/A3.
♥
433 Copy trailing edge void adjustment. Copier 30 0-255 1
♥
435 Printed page leading edge void adjustment. Printer 24 0-255 1
♥
436 Printed page top edge void adjustment (rear Printer 0 0-255 1
of machine). Top of printed page LT/A4 or
right side of ST-R/A5-R, LT-R/A4-R, Legal/B4
and Ledger/A3.
♥
437 Printed page bottom edge void adjustment Printer 0 0-255 1
(front of machine). Top of printed page LT/A4
or left side edge of ST-R/A5-R, LT-R/A4-R,
Legal/B4 and Ledger/A3.
♥
438 Printed page trailing edge void adjustment. Printer 0 0-255 1
♥
442 Bypass registration adjustment. Image on the All 8 0-15 1
drum to the paper’s leading edge.
♥
443 LCC registration adjustment. Image on the All 15 0-40 1
drum to the paper’s leading edge.
Test copy available while in the 05 Mode.
Always perform code 411 first,
then set the value of code 410
to the value set in code 411.
When the value is increased
by 1, the image on the drum is
shifted by 0.0423mm to the
rear of the copier(primary
scanning direction). Refer to
the complete adjustment
procedure before performing
this adjustment.
Laser power increases
2.34É W/step.
Set to 103 do not change from
the setting.
Increasing the value by 1
increases the void by
approximately 0.04233mm.
Increasing the value by 1
increases the void by
approximately 0.04233mm.
Increasing the value by 1
increases the void by approxi-
mately 0.04233mm.
Increasing the value by 1
increases the void by approxi-
mately 0.04233mm.
Increasing the value by 1
increases the void by
approximately 0.04233mm.
Increasing the value by 1
increases the void by
approximately 0.04233mm.
Increasing the value by 1
increases the void by
approximately 0.04233mm.
Increasing the value by 1
increases the void by approxi-
mately 0.04233mm.
Increasing the value by 1
shifts the image on the paper
by approximately 0.5mm
towards the paper’s leading
edge. Increasing the value
makes the paper arrive later.
Increasing the value by 1
shifts the image on the paper
by approximately 0.5mm
towards the papers’ leading
edge. Increasing the value
makes the paper arrive later.