SEW MOVIFIT SC series Operating Instructions Manual Download

Page: 106 / 148

Operation

MOVIFIT® SC operating displays

106

Operating Instructions – MOVIFIT

States of the
"BUS-F" LED

The following table shows the states of the "BUS-F" LED:

States of the
"RUN" LED

The following table shows the states of the "RUN" LED:

SYS-F

BUS-F

RUN

Function

level

Meaning

Troubleshooting

Off

Green

• • •

MOVIFIT

is currently

exchanging data with the DP
master (data exchange).

–

Flashing
red

Green

• • •

•

The baud rate is detected.
However, MOVIFIT

is not

addressed by the DP
master.

•

MOVIFIT

was not

configured or configured
incorrectly in the DP
master

•

Check configuration of
the DP master.

•

Check whether all the
modules configured
during project planning
are permitted for the
MOVIFIT

versions

(MC, FC, SC).

Red

Green

• • •

•

Connection to the DP
master has failed.

•

MOVIFIT

does not detect

baud rate.

•

Bus interruption

•

DP master not in operation

•

Check the PROFIBUS
DP connection of
MOVIFIT

•

Check the DP master

•

Check ppp all cables in
your PROFIBUS DP
network

X
•

Any state
Valid for selected function level:
C = Function level "Classic"
T = Function level "Technology"
S = Function level "System"

SYS-F

BUS-F

RUN

Function

level

Meaning

Troubleshooting

Off

• • •

•

MOVIFIT

not ready for

operation

•

DC 24 V power supply is
not present.

•

Check DC 24 V voltage
supply.

•

Switch MOVIFIT

again. Exchange EBOX
if problem occurs
repeatedly.

Green

• • •

MOVIFIT

components

hardware OK.

–

Off

Green

• • •

•

Correct MOVIFIT

operation.

•

MOVIFIT

is currently

exchanging data with
the DP master (data
exchange) and all subordi-
nate drive systems.

–

Flashing
green

• • •

PROFIBUS address is set
equal to 0 or higher than 125.

Check the PROFIBUS
address set in the MOVIFIT

ABOX.

Yellow

• •

MOVIFIT

is currently in the

initialization phase.

–

Red

•

Internal unit fault

Switch MOVIFIT

on again.

Exchange EBOX if problem
occurs repeatedly.

X
•

Any state
Valid for selected function level:
C = Function level "Classic"
T = Function level "Technology"
S = Function level "System"

Summary of Contents for MOVIFIT SC series





















































































































































Search results

Summary of Contents for MOVIFIT SC series

Reviews:

Related manuals for MOVIFIT SC series

Brands by name

Popular brands

SEW MOVIFIT SC series, Operating Instructions Manual

Search results

Summary of Contents for MOVIFIT SC series

Reviews:

Related manuals for MOVIFIT SC series

Brands by name

Popular brands