SEW MOVIFIT SC series Operating Instructions Manual Download Page 108

Page: 108 / 148

Operation

MOVIFIT® SC operating displays

108

Operating Instructions – MOVIFIT

States of the
"BF" LED

States of the
"SF" LED

RUN

Function

level

Meaning

Troubleshooting

Green

Off

• •

MOVIFIT

is currently

exchanging data with
the PROFINET master
(data exchange)

–

Green

Flashing
green,
flashing
green/red

• •

The flashing function in the
PROFINET master configura-
tion is activated to visually
localize the stations.

–

Green

Red

• •

•

Connection to the
PROFINET master has
failed.

•

MOVIFIT

does not detect

baud rate.

•

Bus interruption

•

PROFINET master not in
operation.

•

Check the PROFINET
connection of the
MOVIFIT

•

Check the PROFINET
master.

•

Check all cables in your
PROFINET mains.

X
•

Any state
Valid for selected function level:
C = Function level "Classic"
T = Function level "Technology"
S = Function level "System"

RUN

Function

level

Meaning

Troubleshooting

Off

• •

•

Normal operating state

•

MOVIFIT

is exchanging

data with the connected
drive systems (MOVIMOT

integrated FC/SC).

–

Red

•

MOVIFIT

FC/SC cannot

exchange data with the inte-
grated FC/SC.

Check the DC 24 V voltage
supply and wiring of the
FC/SC.

Flashing
red

•

No PLC application program
loaded.

Load an application program
and, if necessary, restart the
integrated PLC.

Flashing
yellow

•

PLC application program
stopped.

Check the application
program using MOVITOOLS

MotionStudio and, if neces-
sary, restart the integrated
PLC.

X
•

Any state
Valid for selected function level:
C = Function level "Classic"
T = Function level "Technology"
S = Function level "System"

Summary of Contents for MOVIFIT SC series





















































































































































Search results

Summary of Contents for MOVIFIT SC series

Reviews:

Related manuals for MOVIFIT SC series

Brands by name

Popular brands

SEW MOVIFIT SC series, Operating Instructions Manual

Search results

Summary of Contents for MOVIFIT SC series

Reviews:

Related manuals for MOVIFIT SC series

Brands by name

Popular brands