SEW MOVIFIT SC series Operating Instructions Manual Download

Page: 92 / 148

Startup

Startup instructions

Operating Instructions – MOVIFIT

Startup

7.1

Startup instructions

DANGER

You must disconnect the MOVIFIT

EBOX from the mains before removal/installation.

Severe or fatal injuries from electric shock.
• Disconnect the MOVIFIT

from the mains using an appropriate external discon-

necting device and secure it against unintentional reconnection to the voltage
supply.

• Then wait at least one minute.

WARNING

The surface temperature of the MOVIFIT

can be very high during operation.

Danger of burns
• Touch the MOVIFIT

only when it has sufficiently cooled.

STOP!

• Never remove the MOVIFIT

SC EBOX during operation. Doing so can lead to

dangerous electric arcs forming between the EBOX and the ABOX, which can
cause irreparable damage to the unit (risk of fire, irreparable contacts).

Summary of Contents for MOVIFIT SC series





















































































































































Search results

Summary of Contents for MOVIFIT SC series

Reviews:

Related manuals for MOVIFIT SC series

Brands by name

Popular brands

SEW MOVIFIT SC series, Operating Instructions Manual

Search results

Summary of Contents for MOVIFIT SC series

Reviews:

Related manuals for MOVIFIT SC series

Brands by name

Popular brands