SEW MOVIFIT SC series Operating Instructions Manual Download Page 97

Page: 97 / 148

Startup

Startup MOVIFIT®

Operating Instructions – MOVIFIT

4. To start up the MOVIFIT

motor starter, see the section "Startup MOVIFIT

motor

starter" on page 100.

5. Mount MOVIFIT

EBOX on the ABOX and connect.

6. Switch on supply voltage(s) 24V-C and 24V-S. The associated control LEDs should

now light up green.

Bus termination

The bus terminating resistors are already installed in the MOVIFIT

ABOX (only for

ABOX with terminals and cable glands "MTA...-S02.-...-00") and can be activated using
the S1 switch (

page 13 and following). See the following table:

The following table shows the operating principle of the bus termination switch:

Bus termination ON = on

Bus termination OFF = off

(factory setting)

Bus termination switch S1

Bus termination ON = on

Bus termination OFF = off

57271AEN

57272AEN

OFF

Bus

termination

Incoming

cable

Outgoing

cable

Switch

OFF

Bus

termination

Incoming

cable

Outgoing

cable

Switch

NOTE

When using Hybrid ABOX "MTA...-S12.-...-00" or "MTA...-S22.-...-00" or HanModular

ABOX "MTA...-H12.-...-00" or "MTA...-H22.-...-00" please note:
• In contrast to the version with terminals, these connection boxes require a plug-in

bus terminator (M12) at the last station instead of the outgoing bus connection.

Summary of Contents for MOVIFIT SC series





















































































































































Search results

Summary of Contents for MOVIFIT SC series

Reviews:

Related manuals for MOVIFIT SC series

Brands by name

Popular brands

SEW MOVIFIT SC series, Operating Instructions Manual

Search results

Summary of Contents for MOVIFIT SC series

Reviews:

Related manuals for MOVIFIT SC series

Brands by name

Popular brands