Selco Genesis 4000 MSE, Instruction Manual

Page: 44 / 376

44
757 Wire speed reading
Allow the value of the motor encoder 1 to be displayed.
760 (Motor) Current reading
Allow the real value of the (motor) current to be dis-
played.
765 Coolant temperature reading
Allow the real value of coolant temperature reading to
be displayed.
801 Guard limits
Allows the setting of the warning limits and of the guard
limits.
Allows the accurate control of the various welding
phases (consult the “Guard limits” section).
851 ARC-AIR enabling
On=Active, Off=No active
List of set up parameters (MIG/MAG)
0 Save and quit
Allows you to save the changes and exit the set up.
1 Reset
Allows you to reset all the parameters to the default
values.
2 Synergy
Allows selection of the manual MIG ( ) or syner-
gic MIG ( ) process by setting the type of mate-
rial to be welded.
(Consult the “Synergic curves screen” section).
3 Wire speed
Allows the regulation of the wire feed rate.
Minimum 0.5 m/min, Maximum 22 m/min
4 Current
Allows the regulation of the welding current.
Minimum 6A, Maximum Imax
5 Part thickness
Allows the thickness of the part being welded to be set.
Allows the setting of the system via the regulation of the
part being welded.
6 Corner bead
Lets you set bead depth in a corner joint.
7 Arc length
Allows regulation of the arc length during welding.
Minimum -5.0, M5.0, Default syn
10 Pre-gas
Allows you to set and adjust the gas flow prior to striking
of the arc.
Permits filling of the torch with gas and preparation of
the environment for welding.
Minimum off, Maximum 25 sec., Default 0.1 sec.
11 Soft start
Permits adjustment of the wire feed speed in the phases
prior to arc striking.
Given as a % of the wire speed set.
Permits striking at reduced speed, therefore softer and
with less spatter.
Minimum 10%, Maximum 100%, Default 50%
12 Motor slope
Allows you to set a gradual transition between the
sparking wire speed and the welding wire speed.
Minimum off, Maximum 1.0 sec., Default off
15 Burn back
Permits adjustment of the wire burn time, preventing
sticking at the end of welding.
Permits adjustment of the length.
Permits adjustment of the length of the piece of wire
outside the torch.
Minimum -2.00, M2.00, Default 0.00
16 Post-gas
Permits setting and adjustment of the gas flow at the
end of welding.
Minimum off, Maximum 10 sec., Default 2 sec.
19 Duty cycle (double pulsed)
Permit adjustment of the duty cycle in double pulse.
Parameter setting: percentage (%).
Minimum 10%, Maximum 90%, Default 50%
20 Double pulsed
Allows enablement of the “Double Pulsed” function.
Allows regulation of the pulsation amplitude.
Parameter setting: percentage (%).
Minimum 0%, Maximum 100%, Default ±25%
Parameter setting: meters per minute (m/min).
Minimum 0.5m/min, Maximum 22m/min, Default
2.5m/min
21 Pulse frequency
Allows the impulse frequency to be regulated.
Minimum 0.1Hz, Maximum 5.0Hz, Default 2.0Hz
22 Secondary voltage
Allows regulation of the secondary pulsation level voltage.
Makes it possible to obtain greater arc stability during
the various pulsation phases.
Minimum -5.0, M5.0, Default syn
23 Pulsed slopes (double pulsed)
Allows setting of a slope time during the pulse operation.
Parameter setting: percentage (%).
Minimum 1%, Maximum 100%, Default off
24 Bilevel (4 Step - crater filler)
Permits adjustment of the secondary wire speed in the
bilevel welding mode.
If the welder now presses and releases the button quickly,
“ ” can be used; by pressing and releasing it quickly
again, “ ” is used again, and so on.
Parameter setting: Percentage (%).
Minimum 1%, Maximum 99%, Default off
25 Initial increment
Allows regulation of the wire speed value during the
first “crater-filler” welding phase.
Makes it possible to increase the energy supplied to
the part during the phase when the material (still cold)
requires more heat in order to melt evenly.
Minimum 20%, Maximum 200%, Default 120%
26 Crater filler
Allows regulation of the wire speed value during the weld
closing phase.
Makes it possible to reduce the energy supplied to the part
during the phase when the material is already very hot,
thus reducing the risk of unwanted deformations.
Minimum 20%, Maximum 200%, Default 80%