Samsung S3C2500B User Manual Download Page 333 | Manualshive

Page: 333 / 623

background image

S3C2500B

ETHERNET CONTROLLER

7-23

7.4.1.11 BDMA Receive Frame Size Register

Table 7-24. BDMARXLEN Register

Registers

Address

R/W

Description

Reset Value

BDMARXLENA

0xF00A0028

R/W

Receive frame size

Undefined

BDMARXLENB

0xF00C0028

R/W

Receive frame size

Undefined

Table 7-25. BDMA Receive Frame Size Register Description

Bit Number

Bit Name

Description

[11:0]

BDMA Rx Buffer Size
(BRxBS)

This register value specifies the buffer size allocated to each
buffer descriptor. Thus, for an incoming frame larger than the
BRxBS, multiple buffer descriptors are used for the frame
reception.

NOTE:

BRxBS value has to keep multiples of 16 in byte unit.

For long packet reception larger than 1518 bytes, the BRxBS
should be at least 4 bytes larger than the BRxMFS or less
than 1518 bytes for the reception with a single or multiple
buffer descriptor, respectively.

[15:12]

Reserved

Not applicable

[27:16]

BDMA Maximum Rx Frame
Size (BRxMFS)

This register value controls how many bytes per frame can be
saved to memory. If the received frame size exceeds these
values, an error condition is reported.

NOTE:

BRxMFS value has to keep multiples of 16 in byte unit.

[31:28]

Reserved

Not applicable

«
...
331
332
333
334
335
...
»

Summary of Contents for S3C2500B
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S3C2500B

AllShare Cast Dongle

Brand: Samsung Pages: 2

Brand: D-Link Pages: 14

Brand: Paradyne Pages: 12

NetLink 2960 RAS

Brand: Patton electronics Pages: 2

MegaRAID SCSI 320-2X

Brand: LSI Pages: 4

RabbitCore RCM4400W

Brand: Rabbit Pages: 126

Brand: u-blox Pages: 29

IPAM-1600s Series

Brand: C-Com Pages: 148

RanaSystems 13-0010--001

Brand: RANA Systems Pages: 328

Brand: SYNTEK Pages: 41

UniFi WiFi BaseStation XG

Brand: Ubiquiti Pages: 19

Emotron OSTO 100

Brand: CG Pages: 112

Brand: ICOP Technology Pages: 34

Brand: JETWAY Pages: 63

Brand: Renesas Pages: 6

Brand: Freescale Semiconductor Pages: 124

FiberTwist XGS2410

Brand: Genexis Pages: 7

Brand: Carrier Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands