Samsung S3C2500B User Manual Download Page 36

Page: 36 / 623

PRODUCT OVERVIEW

S3C2500B

1-2

1.2 FEATURES

ARM940T Core processor

•

Fully 16/32-bit RISC architecture.

•

Harvard cache architecture with separate 4KB
Instruction and Data cache

•

Protection unit to partition memory and set
individual protection attributes for each partition

•

AMBA Bus architecture

•

Up to 166MHz operating frequency

Memory Controller

•

24-Bit External Address Pins

•

2 Banks for SDRAM with 16/32-bit external bus.

•

8 Banks for Flash/ROM/SRAM/External I/O with
8/16/32-bit external bus.

•

One External Bus Master with Bus
Request/Acknowledge Pins

Ethernet Controllers

•

Buffered DMA (BDMA) engine using burst mode

•

BDMA Tx/Rx buffers (256-byte/256-byte)

•

MAC Tx/Rx FIFOs (80-byte/16-byte) to support
re-transmit after collision without DMA request

•

Data alignment logic

•

Support for old and new media (compatible with
existing 10M-bit/s networks)

•

10/100 Mbps operation to increase
price/performance options and to support
phased conversions

•

Full IEEE 802.3 compatibility for existing
applications

•

Media Independent interface (MII) or 7-wire
interface

•

Station management (STA) signaling for
external physical layer configuration and link
negotiation

On-chip CAM (21 addresses)

•

Full-duplex mode for doubled bandwidth

•

Pause operation hardware support for full-
duplex flow control

•

Long packet mode for specialized environments

•

Short packet mode for fast testing

•

PAD generation for ease of processing and
reduced processing time

HDLC Controllers and Three TSAs

•

Four address station registers and one mask
register for address search mode

•

Selectable CRC/No-CRC mode

•

Automatic CRC generator pre-set

•

Digital PLL block for clock recovery

•

Baud rate generator

•

NRZ/NRZI/FM/Manchester data formats for
Tx/Rx

•

Loop-back and auto-echo mode

•

Tx and Rx FIFOs with 8-word (8

32-bit) depth

•

Data alignment logic

•

Hardware flow control

•

Embedded DMA Controller with Buffer
Descriptor for Tx/Rx channel

Universal Serial Bus (USB)

•

USB specification 1.1 compliant

•

Full speed 12 Mbps operation with internal
transceiver only

•

A total of 5 endpoints: 1 control endpoint and 4
data endpoints that can support control,
interrupt, bulk transaction.

•

Two data endpoints have 32-byte FIFO, two
data endpoints have 64-byte FIFO.

•

General DMA support

Summary of Contents for S3C2500B
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for S3C2500B

Reviews:

Related manuals for S3C2500B

Brands by name

Popular brands

Samsung S3C2500B, User Manual

Search results

Summary of Contents for S3C2500B

Reviews:

Related manuals for S3C2500B

Brands by name

Popular brands