Samsung S3C2500B User Manual Download Page 508 | Manualshive

Page: 508 / 623

background image

S3C2500B

GDMA CONTROLLER

12-1

12

GDMA CONTROLLER

12.1 OVERVIEW

The S3C2500B has a six-channel General DMA controller, called the GDMA. The six-channel GDMA performs
the following data transfers without CPU intervention:

•

Memory-to-Memory (Memory to/from Memory, Memory to/from USB)

•

External Device-to-Memory (External Device to/from Memory)

•

HUART0/1-to-Memory (High-speed UART serial port0/1 to/from Memory)

•

DES-to-Memory (DES to/from Memory)

The on-chip GDMA can be started by software and/or an external GDMA request (xGDMA_Req), HUART0
request, HUART1 request, or DES request. Software can also be used to restart a GDMA operation after it has
been stopped.

The CPU can recognize when a GDMA operation has been completed by software polling and/or when it receives
an appropriate internally generated GDMA interrupt. The S3C2500B GDMA controller can increment or
decrement source destination addresses and conduct 8-bit (byte), 16-bit (half-word) or 32-bit (word) data transfer.

The GDMA does not check the cache coherency. So software must ensure that source and destination addresses
must be configured as non-cacheable in the memory system configuration when it configures the GDMA
channels.

The local priority of six-channel GDMA can be programmed by fixed priority or round-robin priority in similar
manner to the AHB bus priority. Please refer to Chapter 4, The System Configuration.

12.2 FEATURE

•

Six GDMA Channels

•

Memory to Memory Data Transfer

•

Memory to Peripheral Data Transfer (High Speed UART, DES, USB)

•

Support for Four External GDMA Request from GDMA Request Pins (xGDMA_Req0 – xGDMA_Req3)

«
...
506
507
508
509
510
...
»

Summary of Contents for S3C2500B
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S3C2500B

ShareCenter DNS-320L

Brand: D-Link Pages: 4

Brand: Jabra Pages: 15

Brand: Paradyne Pages: 85

Brand: ICP DAS USA Pages: 8

Brand: ADS Technologies Pages: 1

640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU

Brand: Intel Pages: 105

Brand: MA lighting Pages: 49

Brand: ETAS Pages: 84

Developer's Board

Brand: Sony Ericsson Pages: 28

Brand: ATI Technologies Pages: 87

Brand: B&B Electronics Pages: 24

Brand: ADLINK Technology Pages: 95

Brand: Xtreme Pages: 83

Brand: Hameg Pages: 46

Brand: Addi-Data Pages: 20

Brand: Adeunis RF Pages: 9

Brand: protech Pages: 110

Brand: Cambium Networks Pages: 208

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands