Samsung S3C2500B User Manual Download Page 390 | Manualshive

Page: 390 / 623

background image

HDLC CONTROLLER

S3C2500B

8-30

8.7.2 HDLC CONTROL REGISTER

Table 8-9. HCONA , HCONB, and HCONC Register

Registers

Address

R/W

Description

Reset Value

HCONA

0

×

F0100004

R/W

HDLC channel A control register

0x00000000

HCONB

0

×

F0110004

R/W

HDLC channel B control register

0x00000000

HCONC

0

×

F0120004

R/W

HDLC channel C control register

0x00000000

Table 8-10. HCON Register Description

Bit

Number

Bit Name

Description

[0]

Tx reset (TxRS)

Set this bit to '1' to reset the Tx block. Tx block comprises HTxFIFO and
a transmitter block.

[1]

Rx reset (RxRS)

Set this bit to '1' to reset the Rx block. Rx block comprises HRXFIFO and
a receiver block.

[2]

DMA Tx reset (DTxRS)

Set this bit to '1' to reset the DMA Tx block.

[3]

DMA Rx reset (DRxRS)

Set this bit to '1' to reset the DMA Rx block.

[4]

Tx enable (TxEN)

When the TxEN bit is '0', the transmitter enters a disabled state and the
line becomes high state. In this case, the transmitter block is cleared
except for the HTxFIFO and the status bits associated with transmit
operation are cleared. Data cannot be loaded into the HTxFIFO.

If this bit is set to '1', the idle pattern is sent continuously. In this case, the
data can be loaded into HTxFIFO, and then sent.

[5]

Rx enable (RxEN)

When the RxEN bit is '0', the receiver enters a disabled state and can not
detect the flag pattern, if any. In this case, receiver block is cleared
except for the HRXFIFO and the status bits associated with receiver
operation are cleared. Data cannot be received.

If this bit is set to '1', the flag pattern is detected. In this case, the data
received can be loaded into the HRXFIFO, and moved to system
memory.

[6]

DMA Tx enable (DTxEN) The DTxEN bit lets the HDLC Tx operate on a bus system in DMA mode.

When DMA Tx is enabled, an interrupt request caused by TxFA status is
inhibited and the HDLC does not use the interrupt request to request a
data transfer. DMA Tx monitors the HTxFIFO and fills the HTxFIFO. This
bit is auto disabled when Tx underrun occurs, or CTS lost, or next buffer
descriptor pointer reach null, or the owner bit is not DMA mode when
DTxSTSK bit is set. If Tx underrun occurs, DTxABT(in HSTAT) bit set,
and abort signal sended. If CTS lost occurs, DTxABT bit set and TxD
output goes high state as long as CTS remains high level.

«
...
388
389
390
391
392
...
»

Summary of Contents for S3C2500B
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S3C2500B

Brand: EAW Pages: 10

Brand: Abus Pages: 60

Brand: Datasat Pages: 32

Avenue Express Control Panel

Brand: Ensemble Designs Pages: 19

Brand: peplink Pages: 2

Brand: EMCIS Pages: 14

Brand: A4Tech Pages: 8

JetStor NAS 724UX

Brand: AC&NC Pages: 117

Brand: MA lighting Pages: 49

Brand: Digi Pages: 75

Ultra WiFi Booster

Brand: Optus Pages: 8

N-FXE 02B Series

Brand: Lantronix Pages: 10

Brand: ENERMAX Pages: 33

Hotwire 5620 RTU

Brand: Paradyne Pages: 20

Brand: IBASE Technology Pages: 49

Brand: ZyXEL Communications Pages: 114

Brand: Jäger Pages: 54

Threat Analysis Reporter TAR HL/SL/MSA

Brand: 8e6 Technologies Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands