Ricoh SP C222DN Administration Manual Download

Page: 269 / 284

Additional Information for Software Installation
Guide for Network Connection

This supplement provides you with additional information for setting up the
printer in a Windows network environment.

If your environment is using DHCP, be sure to read this supplement as well as

Software Installation Guide for Network Connection

before installing the printer

drivers.

When Installing the Drivers in a DHCP Environment

Note the following before installing the printer drivers in a DHCP environment:

❒

Make sure the network cable is properly connected to the printer before you

print the test page.

❒

Omit the procedure in "3. Specify the Printer

’

s IP Address",

Software

Installation Guide for Network Connection

. This procedure is not necessary

because the printer is automatically recognized by its IP address when its main
power is switched to ON.

❒

Using Web Image Monitor, change the automatically specified IP address to

the IP address printed on the test page.

For details about Web Image Monitor, see

Software Guide

on the supplied CD-

ROM and

Notes to Administrator

that is provided with the printer.

2007

Printed in China

GB GB EN USA

G165-7509

G1657509

Summary of Contents for SP C222DN


























































































































































































































































































Search results

Summary of Contents for SP C222DN

Reviews:

Related manuals for SP C222DN

Brands by name

Popular brands

Ricoh SP C222DN, Administration Manual

Search results

Summary of Contents for SP C222DN

Reviews:

Related manuals for SP C222DN

Brands by name

Popular brands