manualshive.com logo in svg

Ricoh SP C222DN, Administration Manual

Share
Download
Ricoh SP C222DN Administration Manual Download Page 140

95

9. Appendix

If the Printer is Not Going to Be Used for a 
Long Time

If the printer is going to be inactive for a long time, follow the procedure shown
here.

R

 

WARNING:

R

 

CAUTION:

Preparing the Printer For a Long Period of Inactivity

Use this procedure to prepare the printer for a long period of inactivity with its
power switch turned to off.
Note that not using the following procedure could result in unusual noises when
use of this printer is resumed.

Important

❒

Do not switch off the printer during printing.

A

Turn off the power switch.

B

Pull out the plug from the socket.

•

Plug and unplug the power cable with dry hands, or an electric shock 
could occur.

•

The inside of this printer becomes very hot. Do not touch parts labelled “

v

” 

(indicating a hot surface).

•

Unplug the power cord from the wall outlet before you move the machine. 
While moving the machine, you should take care that the power cord will 
not be damaged under the machine.

Summary of Contents for SP C222DN





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands