Ricoh SP C222DN Administration Manual Download Page 216

Page: 216 / 284

Using Web Image Monitor

Displaying the Printer Status

Top page of Web Image Monitor contains two tabs: the

[

Status

]

tab and

[

Counter

]

tab.

❖

[

Status

]

tab

You can check the status of monitored printers.
• Displays the general information of the printer, such as the model name,

location and the status.

• Toner

Displays the levels of remaining toner.

• Others

Displays the status of the consumables.

• Input Tray

Displays the input tray status and paper settings.

❖

[

Counter

]

tab

You can check the total number of pages printed to date.
The following counter information is displayed.
• Total
• Black&White
• Full Color
• Two Sided Print

About Menu and Mode

There are two modes available with Web Image Monitor: user mode and admin-
istrator mode.
The available menus on the

[

Configuration

]

page differ depending on the mode

you are logging on.

Summary of Contents for SP C222DN


























































































































































































































































































Search results

Summary of Contents for SP C222DN

Reviews:

Brands by name

Popular brands

Ricoh SP C222DN, Administration Manual

Search results

Summary of Contents for SP C222DN

Reviews:

Brands by name

Popular brands