Ricoh SP C222DN Administration Manual Download Page 101

Page: 101 / 284

Replacing Consumables

Replacing the Waste Toner Bottle

WARNING:

CAUTION:

❖

When to replace the waste toner bottle

If the

Alert

indicator lights up and the message “

Waste Toner Bottle

Full. The Waste Toner Bottle is full. Open the indicated cover,

and then replace the Waste Toner Bottle. Front Cover : [Waste

Toner Bottle].

” appears on the Smart Organizing Monitor dialog box, re-

place the waste toner bottle.

Important

❒

Waste toner bottles cannot be reused.

❒

Purchasing and storing extra waste toner bottles are recommended.

❒

When removing the waste toner bottle, make sure not to tilt it.

❒

Keep the waste toner bottle horizontal as you take it out.

❒

Make sure the transfer unit is installed. If the transfer unit is not installed, in-
stall it before turning the power on.

❒

Cooperate with the waste toner bottle Recycling Program, whereby used
waste toner bottles are collected for recycling.

•

Do not incinerate spilled toner or used toner. Toner dust might ignite
when exposed to an open flame.

•

Wait at least 30 minutes after disconnecting the power plug before re-
moving the transfer unit.

•

Do not incinerate used toner or toner containers. Toner dust might ig-
nite when exposed to an open flame. Dispose used toner containers in
accordance with local regulations.

•

The inside of this printer becomes very hot. Do not touch parts labelled “

”

(indicating a hot surface).

•

Keep toner (used or unused) and toner containers out of reach of children.

Summary of Contents for SP C222DN


























































































































































































































































































Search results

Summary of Contents for SP C222DN

Reviews:

Brands by name

Popular brands

Ricoh SP C222DN, Administration Manual

Search results

Summary of Contents for SP C222DN

Reviews:

Brands by name

Popular brands