Ricoh SP C222DN Administration Manual Download Page 118

Page: 118 / 284

Error & Status Messages on Smart Organizing Monitor

Cover Open

Close the indicated cover.

[Top or Front Cover]

The top cover or front cover is
open.

Open and then close the top
cover or front cover.

Unit Not Detected

Open the indicated cover, and
then check the Toner Car-
tridge.

Top Cover : [Black]

The indicated print cartridge
is not set correctly, or not set.

(Black)

Set the indicated print car-
tridge correctly.

(Black)

The error message appears
even though the print car-
tridge is set correctly.

Using a dry cloth, carefully
wipe the interface area on the
print cartridge surface.

Unit Not Detected

Open the indicated cover, and
then check the Toner car-
tridge.

Top Cover : [Magenta]

The indicated print cartridge
is not set correctly, or not set.

(Magenta)

Set the indicated print car-
tridge correctly.

(Magenta)

The error message appears
even though the print car-
tridge is set correctly.

Using a dry cloth, carefully
wipe the interface area on the
print cartridge surface.

Unit Not Detected

Open the indicated cover, and
then check the Toner car-
tridge.

Top Cover : [Cyan]

The indicated print cartridge
is not set correctly, or not set.

(Cyan)

Set the indicated print car-
tridge correctly.

(Cyan)

The error message appears
even though the print car-
tridge is set correctly.

Using a dry cloth, carefully
wipe the interface area on the
print cartridge surface.

Unit Not Detected

Open the indicated cover, and
then check the Toner Car-
tridge.

Top Cover : [Yellow]

The indicated print cartridge
is not set correctly, or not set.

(Yellow)

Set the indicated print car-
tridge correctly.

(Yellow)

The error message appears
even though the print car-
tridge is set correctly.

Using a dry cloth, carefully
wipe the interface area on the
print cartridge surface.

Unit Not Detected

The Waste Toner Bottle is not
set, or is not set properly.

[Waste Toner Bottle]

There is no waste toner bottle,
or the waste toner bottle is not
installed correctly.

Set the waste toner bottle cor-
rectly.

Controller FW download
failed.

Controller FW could not be
downloaded.

Wait for a while and do not
turn off the power.

No Toner

The following toner has run
out.

Open the indicated cover, and
then replace the Toner Car-
tridge.

Top Cover : [Black]

The printer is out of toner
(Black).

Replace the print cartridge
(Black).

See p.51 “Replacing the Print
Cartridge”

Message

Explanation

Recommended Action

Summary of Contents for SP C222DN


























































































































































































































































































Search results

Summary of Contents for SP C222DN

Reviews:

Brands by name

Popular brands

Ricoh SP C222DN, Administration Manual

Search results

Summary of Contents for SP C222DN

Reviews:

Brands by name

Popular brands