Ricoh SP C222DN Administration Manual Download

Page: 4 / 284

Operating Instructions Hardware Guide

2. Installing the Printer and Options > Installing the Printer > Unpacking
8. Removing Misfed Paper > When Paper is Jammed > When Paper

Jams inside the Fusing Unit
9. Appendix > If the Printer is Not Going to Be Used for a Long Time

> Preparing the Printer For a Long Period of Inactivity
9. Appendix > If the Printer is Not Going to Be Used for a Long Time

> Using the Printer Again after it has been Inactive for a Long Period

Errors

Carefully lift the blue fusing unit levers.

Correction

The procedure above is not necessary.

2. Installing the Printer and Options > Installing the Printer > Unpacking

5. Replacing Consumables > Replacing the Print Cartridge

6. Cleaning the Printer > Cleaning the Toner Density Sensor >

Preparing the Printer For a Long Period of Inactivity

Errors

Close the top cover with both hands carefully.

Correction

Close the top cover with both hands carefully. Be careful not to trap your
fingers.

Printed in China

GB GB EN USA G165-7510

Summary of Contents for SP C222DN


























































































































































































































































































Search results

Summary of Contents for SP C222DN

Reviews:

Related manuals for SP C222DN

Brands by name

Popular brands

Ricoh SP C222DN, Administration Manual

Search results

Summary of Contents for SP C222DN

Reviews:

Related manuals for SP C222DN

Brands by name

Popular brands