Ricoh SP C222DN Administration Manual Download

Page: 151 / 284

Appendix

106

❖

Noise Emission *1

Sound Power Level

Sound Pressure Level *2

*1 : The preceding measurements made in accordance with ISO7779 are actual
values.
*2 : Measured at the position of a bystander.

❖

Memory

• SP C220N:

Standard 64M

• SP C221N/SP C222DN:

Standard 128 MB, up to 320 MB (with the optional memory unit)

❖

Interface

• Ethernet (10/100 Base-TX)
• USB2.0

It requires a USB computer port and cable that support USB 2.0.

• USB Host (1.1)

Note

❒

USB Host (1.1) is only available for the SP C222DN model printer.

❖

Printer Language

• SP C220N:

DDST

• SP C221N/SP C222DN:

PJL, PCL 5c/6, PostScript Level 3, PictBridge

Note

❒

PictBridge is only available for the SP C222DN model printer.

❖

Fonts

• SP C221N/SP C222DN:

PCL
41 Symbolset, 35 Intellifonts, 10 TrueType fonts, 1 bitmap font.
PostScript 3
80 fonts

Mainframe only

Stand-by

43 dB (A)

During Printing

Monochrome: 63 dB (A)

Color: 64 dB (A)

Mainframe only

Stand-by

35 dB (A)

During Printing

57 dB (A)

Summary of Contents for SP C222DN


























































































































































































































































































Search results

Summary of Contents for SP C222DN

Reviews:

Related manuals for SP C222DN

Brands by name

Popular brands

Ricoh SP C222DN, Administration Manual

Search results

Summary of Contents for SP C222DN

Reviews:

Related manuals for SP C222DN

Brands by name

Popular brands