manualshive.com logo in svg

Renesas F-ZTAT H8/3642A Series, Hardware Manual, Page: 370 / 551

Share
Download
Renesas F-ZTAT H8/3642A Series Hardware Manual Download Page 370

Section 12   A/D Converter 

Rev. 6.00  Sep 12, 2006  page 348 of 526 
REJ09B0326-0600 

 

12.2 Register 

Descriptions 

12.2.1 

A/D Result Register (ADRR) 

Bit 

7 6 5 4 3 2 1 0 

 

ADR7 ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 ADR0 

Initial value 

Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined

Read/Write  R R R R R R R R 

 

The A/D result register (ADRR) is an 8-bit read-only register for holding the results of analog-to-
digital conversion. 

ADRR can be read by the CPU at any time, but the ADRR values during A/D conversion are 
undefined. 

After A/D conversion is complete, the conversion result is stored in ADRR as 8-bit data; this data 
is held in ADRR until the next conversion operation starts. 

ADRR is not cleared on reset. 

12.2.2 

A/D Mode Register (AMR) 

Bit 

7 6 5 4 3 2 1 0 

 CKS 

TRGE 

 

  CH3 CH2 CH1 CH0 

Initial 

value  0 0 1 1 0 0 0 0 

Read/Write R/W 

R/W 

 

  R/W R/W R/W R/W 

 

AMR is an 8-bit read/write register for specifying the A/D conversion speed, external trigger 
option, and the analog input pins. 

Upon reset, AMR is initialized to H'30. 

Summary of Contents for F-ZTAT H8/3642A Series








































































































































































































































































































































































































































































































































































Reviews:

No comments