manualshive.com logo in svg

Renesas F-ZTAT H8/3642A Series, Hardware Manual, Page: 319 / 551

Share
Download
Renesas F-ZTAT H8/3642A Series Hardware Manual Download Page 319

Section 10   Serial Communication Interface 

Rev. 6.00  Sep 12, 2006  page 297 of 526 

REJ09B0326-0600 

 

Serial Control Register 3 (SCR3) 

Bit 

7 6 5 4 3 2 1 0 

 TIE 

RIE 

TE 

RE 

MPIE 

TEIE 

CKE1 

CKE0 

Initial 

value  0 0 0 0 0 0 0 0 

Read/Write 

R/W R/W R/W R/W R/W R/W R/W R/W 

 

SCR3 is an 8-bit register for selecting transmit or receive operation, the asynchronous mode clock 
output, interrupt request enabling or disabling, and the transmit/receive clock source. 

SCR3 can be read or written by the CPU at any time. 

SCR3 is initialized to H'00 upon reset, and in standby, watch, subactive, or subsleep mode. 

Bit 7

Transmit interrupt Enable (TIE): 

Bit 7 selects enabling or disabling of the transmit data 

empty interrupt request (TXI) when transmit data is transferred from the transmit data register 
(TDR) to the transmit shift register (TSR), and bit TDRE in the serial status register (SSR) is set to 
1.  

TXI can be released by clearing bit TDRE or bit TIE to 0. 

Bit 7: TIE 

Description 

0 

Transmit data empty interrupt request (TXI) disabled 

(initial value)

1 

Transmit data empty interrupt request (TXI) enabled 

 

Bit 6

Receive Interrupt Enable (RIE): 

Bit 6 selects enabling or disabling of the receive data 

full interrupt request (RXI) and the receive error interrupt request (ERI) when receive data is 
transferred from the receive shift register (RSR) to the receive data register (RDR), and bit RDRF 
in the serial status register (SSR) is set to 1. There are three kinds of receive error: overrun, 
framing, and parity. 

RXI and ERI can be released by clearing bit RDRF or the FER, PER, or OER error flag to 0, or by 
clearing bit RIE to 0. 

Bit 6: RIE 

Description 

0 

Receive data full interrupt request (RXI) and receive error interrupt request 
(ERI) disabled 

(initial value)

1 

Receive data full interrupt request (RXI) and receive error interrupt request 
(ERI) enabled 

 

Summary of Contents for F-ZTAT H8/3642A Series








































































































































































































































































































































































































































































































































































Reviews:

No comments