Regency Fireplace Products Grandview G800EH Owners & Installation Manual Download Page 87

Page: 87 / 104

Grandview

G800EH Gas Fireplace |

maintenance

Light Bulb Replacement - Bottom Lights

Light Bulb Replacement -Top Light

1. Remove screen, glass door, logs and any other media, log grate, and lower

panel (if installed).

2. Remove two (2) screws from light assembly cover in the locations shown

below.

3. Lift up and slide light assembly cover forward to remove.

4. Install or replace bulbs as required.

NOTE:

Do not touch bulbs with bare hands, use gloves or a tissue when handling

bulbs. Part # of each bottom bulb is 911-297. There are 4 per unit.

5. Reverse steps to reassemble unit.

Turn off fireplace and wait until it has reached room temperature.

Remove the Screen Barrier. See Section: Safety screen removal / Instal

lation.

3. Remove the glass door: See Section: Glass door removal / Installation.

4. Remove the two screws with a Phillips-head screwdriver as shown below.

Remove the Top Light Casing by lifting up and out.

6. Remove the old light bulb by pulling out of the socket.

7. Install the new bulb using solf, clean, gloves. Do NOT touch the bulb with

your bare hands. Part # of the top bulb is 911-300.

Reverse steps to re-install. NOTE: Be careful not to pinch the wiring

when re-installing the Top Light Casing. There is a cut-out for the wiring

to route through.

Summary of Contents for Grandview G800EH









































































































Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands

Regency Fireplace Products Grandview G800EH, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands