Regency Fireplace Products Grandview G800EH Owners & Installation Manual Download Page 37

Page: 37 / 104

Grandview

G800EH Gas Fireplace |

installation

Clean Front Installation

Framing

Tab

The finishing material can be brought to the edge of the fireplace opening.

Do NOT finish beyond the opening, doing so will prevent the screen from

being attached and removed.

The Optional Clean Front Trim (Part # 761-929) is available to prevent this

from happening. See Section:

lean

ront

rim

nstall

nstruCtions

for details.

Nailing Flange Instructions

Optional Clean

Front Trim

Optional Clean Front Trim Install Instructions

(Part # 761-929)

Loosen the four (4) screws that at

tach the right and left nailing flanges

to the unit.

Slide the left and right tiling flanges

onto the front of the fireplace. Use the

slots to center with the screw securing

the Nailing Flanges.

Tighten screws down.

Slide the Bottom Tiling Flange against

the bottom of the fireplace. Secure with

a screw on each side.

Finishing material can now be pressed

against the flat edge created by the

Clean Front Trim.

1. Bend framing tabs 90° backward to create the framing standoff.

max.

Summary of Contents for Grandview G800EH









































































































Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands

Regency Fireplace Products Grandview G800EH, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands