Regency Fireplace Products Grandview G800EH Owners & Installation Manual Download Page 82

Page: 82 / 104

| Grandview

G800EH Gas Fireplace

installation

920-133

06.24.19

FAN INSTALLATION

8. Remove centre screw and loosen screw on light assembly as shown.

9. Pivot light assembly out to 90

10. Remove eight (8) screws from fi rebox fl oor access panel.

11. Lift out panel with light assembly and set aside, be careful of light

assembly wiring.

12. Manoeuvre fan assembly onto pins on unit fl oor via fan access opening.

13. Connect the fan to the DFC and ground—follow Steps 5-7 from the

previous page.

TO REMOVE THE FAN

Shut the power off.

2. Reverse the above instructions.

Note:

The bearings are lubricated for life. Do not lubricate

them. Make sure you vacuum the fan area on a regu-
lar basis.

IMPORTANT:

These fans collect a lot of dust from within your home. Ensure you

maintain these fan motors on a regular basis by vacuuming out the

fan blades and housing using a soft brush nozzle.

Diagram 7

Diagram 10

Diagram 8

Diagram 9

Fan Install After Unit Installation

The fan may be installed after the unit has been installed and fin

ished. Ensure the unit is turned off and has cooled to room tempera

ture.

Shut off the power and gas to the unit.

3. Remove the screen and glass door. (See sections: Safety screen

removal / Installation & glass door removal / Installation)

Remove any media already installed (logs, glass, etc.) and set aside.

Remove the log grate.

6. Remove the burner.

7. Remove the firebox floor panel (brick or enamel).

Remove 8 screws from the firebox floor access panel as shown.

8. Remove the screen from the light assembly.

9. Lift out access panel with light assembly and set aside.

10.

Loosen 2 screws off from the IFC box and set aside.

11.

Connect the fan to the IFC and ground (follow Steps 4-6 from the

previous page).

12. To reinstall reverse steps 10 to 2.

Summary of Contents for Grandview G800EH









































































































Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands

Regency Fireplace Products Grandview G800EH, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands