Regency Fireplace Products Grandview G800EH Owners & Installation Manual Download Page 73

Page: 73 / 104

Grandview

G800EH Gas Fireplace |

installation

Crystal Tray Installation

09.29.22

920-199

CRYSTAL TRAY INSTALLATION

Page 1

G800

2. Attach the crystal tray with two screws, one on the middle left

and another on the middle right of the tray, as shown below.

3. Add 7 lbs of crystal media and spread it across the tray in one

even layer.

Important: ensure that at least 50% of the

gas burner porting remains uncovered. Do not cover

the pilot area.

BURNER PORTING

PILOT

4. If using volcanic stones as additional media, add a maximum

of 13, as shown below.

Important: Volcanic stones should

not cover any of the gas burner porting or pilot areas.

Note: The optional brick, steel, or enamel panels must be installed

prior to the crystal tray.

1. Place the crystal tray over the burner, as shown below.

5. To remove the crystal tray, reverse the steps above.

Summary of Contents for Grandview G800EH









































































































Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands

Regency Fireplace Products Grandview G800EH, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands