Regency Fireplace Products Grandview G800EH Owners & Installation Manual Download Page 51

Page: 51 / 104

Grandview

G800EH Gas Fireplace |

installation

(Propane & Natural Gas)

The Diagram shows minimum vent runs with 4" x 6-5/8" venting using the Regency direct vent system or rigid vent system.

A vent guard should be used whenever the termination is lower than the specified minimum or as per local codes.

For horizontal terminations the Regency Direct Vent Flex System may be used for installations with a maximum

continuous

vent maximum horizontal length

of 2ft (0.6 m).

Note: Must use optional rigid pipe adaptor (Part # 510-994) when using Rigid Pipe vent systems.

Maintain clearance to combustibles.

For all other venting arrangements, see Venting Arrangements - Horizontal Termination - Rigid Pipe and Direct Vent System (Flex) in this

manual.

Vertical Height (Feet)

Rigid 44-"(1.1m)

Horizontal (Feet)

Max. 24”(0.6m)

Flex 44"(1.1m)

Top Vented

Set #1 (2" open) up to 1' horizontal

Factory Setting - no restrictor required greater than 1'

horizontal

Venting Arrangements for Horizontal Terminations - Flex Vent/Rigid Pipe

4" x 6-5/8" (102 mm x 168 mm)

Summary of Contents for Grandview G800EH









































































































Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands

Regency Fireplace Products Grandview G800EH, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands