Regency Fireplace Products Grandview G800EH Owners & Installation Manual Download Page 43

Page: 43 / 104

Grandview

G800EH Gas Fireplace |

installation

" (19 mm)

Nailing Flange

Tabs folded

forward

Mounting Tabs

folded forward

Mounting Tab

Folded For-

ward

Nailing Flange

folded forward

Framing

Face Plate

Top View

Install the faceplate by resting the arms on the Face

Plate on top of the mounting tabs.

Adjust left and right to center the Face Plate.

NOTE: Do not to touch the faceplate without clean,

soft, gloves. Dirt or oils can be transferred onto

the finish and become permanent.

Critical Finishing Gap

A 1/2” gap must be maintained on the sides of the

fireplace to allow the Face Plate to be installed and

removed.

Do NOT finish past the front face of the fireplace.

Faceplate Finishing

Summary of Contents for Grandview G800EH









































































































Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands

Regency Fireplace Products Grandview G800EH, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands