Regency Fireplace Products Grandview G800EH Owners & Installation Manual Download Page 81

Page: 81 / 104

Grandview

G800EH Gas Fireplace |

installation

Installing the Optional Fan Prior to Unit Installation Into Framing

(Recommended - Part # 761-917)

920-133

06.24.19

FAN INSTALLATION

1. The fan may be installed after the unit has been installed and fi nished.

Ensure the unit is turned off and has cooled to room temperature.

2. Remove the screen and glass door (see unit manual for details).

3. Remove any media already installed (logs, glass, etc.) set aside.

4. Remove the log grate.

5. Remove the burner.

6. Remove the fi rebox fl oor panel (brick or enamel).

7. Remove screen from light assembly.

Important:

120 Volt AC power is needed for the blower. The receptacle

box will be installed on the left hand side of the unit and will need to

be wired by a qualifi ed electrician prior to fan assembly being installed.

The neutral (wider) slot of the polarized receptacle should be at the top.

Unit must be grounded at all times. Do not cut the ground terminal

off under any circumstances.

1. Shut the power off .

2. Remove the safety screen and glass door (see unit manual for details).

Diagram 1- panel removal

Diagram 3- fan wires

Diagram 2- fan install

4. Install fan assembly onto pins on unit fl oor.

Note: Diagram below shows fan bracket only.

5. Fold access panel cover down and secure with 2 screws.

6. Connect red + black wires to fan assembly.

8. Connect fan ground cable to ground lug (located in lower right corner

of unit). Refer to wiring diagram.

7. Connect red + black fan wires to corresponding red + black wires on

the DFC box as shown.

3. From the back of the unit—remove 2 screws from the fan access panel

(locations shown below). Gently fold panel cover upwards.

FAN INSTALLATION PRIOR TO INSTALLATION

FAN INSTALL AFTER UNIT INSTALLATION

Diagram 4- fan wires

Diagram 5- DFC wires

Diagram 6- ground wires

3. From the back of the unit - remove 4 screws from the fan access

panel (locations shown below).

4. Connect red + black fan wires to corresponding red + black wires

on the IFC box as shown

5. Connect fan ground cable to ground lug (located in lower right

corner of unit). Refer to wiring diagram.

7. Secure fan access panel back onto the unit with 4 screws (loca

tions shown below).

6. Install fan assembly onto pins on unit floor.

Important: 120 Volt AC power is needed for the blower. The

receptacle box will be installed on the right hand side of the unit and

will need to be wired by a qualified electrician prior to fan assembly

being installed. The neutral (wider) slot of the polarized receptacle

should be at the top.

Unit must be grounded at all times. Do not cut the ground

terminal off under any circumstances.

1. Shut the power off.

2. Remove the safety screen and glass door (see unit manual for

details).

Summary of Contents for Grandview G800EH









































































































Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands

Regency Fireplace Products Grandview G800EH, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands