Regency Fireplace Products Grandview G800EH Owners & Installation Manual Download Page 77

Page: 77 / 104

Grandview

G800EH Gas Fireplace |

installation

IMPORTANT INSTALLATION NOTE:

The Battery Holder must be placed inside the supplied (Low Voltage) junction type wall box and installed into the wall only.

DO NOT INSTALL WITHIN THE CONFINES OF THE FIREPLACE

SWITCH MUST BE ACCESSIBLE

Battery Holder Installation

1. Install the low voltage junction box to the framing at the desired location, within 12 ft. from fireplace.

2. Feed the 6 pin connector wiring harness through the opening at the back of the junction box. The wiring harness is located near the

gas valve and must be routed to the exterior of the fireplace from either the left or right side prior to finishing.

3. Connect the 6 pin connector to the back of the battery holder.

4. Install the battery holder in the low voltage junction box.

5. Install batteries

only

if 120 volt power will not be used. Batteries usually serve as a secondary power source. Insert the 4 AA type bat

teries in the battery compartment with the correct polarity.

6. Place the slider into the cover plate.

7. Put the battery holder switch in the “OFF” position, to allow correct lineup for slider switch.

8. Make sure the battery holder and cover plate words “ON” and “UP” are on the same side.

9. Align the slider with the switch on the battery holder and couple the switch into the slider.

10. Align the screw holes.

11. Using the two (2) screws provided secure the cover plate to the battery holder.

12. For coding inst

ructions, see full details in this manual.

Proflame Battery Holder

Wall Mount On/Off Switch and Battery Holder Installation

Required for All installations

REMOTE

OFF

Item

Part No.

Description

N/A

Slider Switch (included with

wall plate)

911-335

Wall Plate - White

911-343

Wall Plate - Black

911-337/P

Battery Holder

N/A

J-Box

910-369

Low Voltage Junction Box

911-181

Battery Holder Wire Harness

Summary of Contents for Grandview G800EH









































































































Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands

Regency Fireplace Products Grandview G800EH, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands