Regency Fireplace Products Grandview G800EH Owners & Installation Manual Download Page 70

Page: 70 / 104

| Grandview

G800EH Gas Fireplace

installation

09.29.22

920-127a

LOG SET INSTALLATION

Page 2 of 4

4. Install 2 log support plates onto the burner with 2 screws each

as shown.

5. Place Log 1 onto the grate, behind the rear of the burner. Ensure

the left cut out butts against the end of the burner tube and the

right end of the log butts against the curve of the burner. Final

position of the log should be pulled forward and to the right while

contacting the end and curved parts of the burner.

6. Install Log 2 on left log support plate. Line up the pins on the

plate with the pin hole on the log.

7. Install Log 3 on right log support plate. Line up the pins on the

plate with the pin hole on the log.

8. Install Log 4 diagonally across Log 2. Rest Log 4 in the notch out

on Log 2 as shown.

Diagram 5—Install Log support plates

Diagram 10—Install Log 4

Diagram 8—Install Log 2

Diagram 9—Install Log 3

Diagram 6—Log support plates installed

Diagram 7—Log 1 installation

Log Support Plates

G800

Summary of Contents for Grandview G800EH









































































































Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands

Regency Fireplace Products Grandview G800EH, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands