Regency Fireplace Products Grandview G800EH Owners & Installation Manual Download Page 69

Page: 69 / 104

Grandview

G800EH Gas Fireplace |

installation

Log Set Installation

09.29.22

920-127a

LOG SET INSTALLATION

Page 1 of 4

Rear Log

Middle Left Log

Middle Right Log

Center Left Cross Log

Front Bottom 'Y' Log

Left Rear Log

Right Cross Log

Middle Front

Left Log Piece

Right Log Piece

Left Front Log Piece

Right Front Log Piece

Must also purchase (#761-938) Log

Grate and Ember package separately.

The kit contains:

Log Grate
3/4" Ginger glass
Vermiculite
Black/White Embers
Log Support Plates

Read the instructions below carefully and refer to the dia-

grams. If logs are broken do not use the unit until they are

replaced. Broken logs can interfere with the pilot operation.

The G800 log sets, #761-930 for Oak, #761-932 for Birch, contain

the following pieces:

NOTE: Panels (brick, steel, or enamel) must be installed

prior to installing the log set.

1. Carefully remove the logs from the box and unwrap them. The

logs are fragile, handle with care -

do not force into position

when installing.

2. Install the log grate—secure with 2 screws in locations show below.

3. Install the supplied crystals over the ember lights underneath the

burner as shown. Place vermiculite and embers on top of the glass.

Do not place any media on the burner.

Diagram 1—Log ID

Diagram 2—Log Grate Install

Diagram 3—Install Glass

Diagram 4—Install Vermi Lava

G800

Summary of Contents for Grandview G800EH









































































































Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands

Regency Fireplace Products Grandview G800EH, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands