Regency Fireplace Products Grandview G800EH Owners & Installation Manual Download Page 24

Page: 24 / 104

| Grandview

G800EH Gas Fireplace

installation

Unit Assembly Prior to Installation (Nailing Flange Installation)

Left Nailing Flange

Right Nailing Flange

Standoff Deflector

Top Nailing Flange

Finishing

Material

Depth

Front of Fireplace

1-1/4”

3/4”

1/4”

1”

1/2”

Flush

After the framing has been built, the nailing Flanges

will need to be set depending on the depth of finish

ing material being used. Up to 1-1/4” total material

thickness can be used, including the backing mate

rial. The depth of finishing material can be adjusted

in 1/4” increments.

1. Determine the required depth setting for the

materials being used.

Once the setting has been chosen, install the

Left and Right Nailing Flanges with 2 screws

on each Flange.

Nailing Flange Parts

Summary of Contents for Grandview G800EH









































































































Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands

Regency Fireplace Products Grandview G800EH, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands