Regency Fireplace Products Grandview G800EH Owners & Installation Manual Download Page 68

Page: 68 / 104

| Grandview

G800EH Gas Fireplace

installation

Enamel/Steel Panel Installation (Steel Panels - Part # 761-907, Enamel Panels - Part # 761-908)

09.29.22

920-128b

ENAMEL/STEEL PANEL INSTALLATION

5. Loosen screws and remove brick clips.

1. Remove screen and glass door, if installed.

2. Loosen two screws in locations shown below. Slide upper baffle

towards the back wall and then remove from unit.

6. Install the right side panel—the angled corner should be located

facing the bottom rear of the fireplace when installing.

NOTE:

Shorter row of bricks should be positioned at the bottom of

back and side panels.

7. With panel in position, secure it with the brick clip removed in Step

5 and retighten the screw.

For Black Enamel Panels:

• Black enamel panels must be inspected for scratches and dimples

prior to installation. All claims are to be recorded at this time. Claims

for damage after installation will not receive consideration.

• Black enamel panels will discolor a little during normal operation.

This is normal and should not be considered a defect.

* All hand and fingerprints MUST be cleaned off with a soft cloth.

Use an ammonia-based cleaner (ie. glass cleaner) to remove any

fingerprints before applying heat to the unit.

Failure to do this will result in burn stains on panels which

you will be unable to remove. Not protected by product

warranty.

G800

3. Loosen 2 screws on pilot assembly in locations shown below. Slide

pilot shield towards the back of the unit and remove from unit.

8. Repeat Steps 5-7 on the left side.

4. Install back panel carefully. Tilt panel forward from the top and

rest the bottom of the panel on the firebox floor. Tip top back until

it also rests on the firebox back wall.

10. Reinstall the upper baffle.

11. Reinstall the pilot shield removed in step 3.

9. Slide the bottom panel carefully underneath the burner and

push to the back until it contacts the back panel.

Note: Do not install the firebed grate, media, vermiculite, embers,

and logs until the enamel/steel panels are installed.

tooltip

Item

Part #

Description

N/A

Inside Top of

Firebox

N/A

Panel

761-049

Brick Clip

904-519

Screw

Summary of Contents for Grandview G800EH









































































































Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands

Regency Fireplace Products Grandview G800EH, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800EH

Reviews:

Related manuals for Grandview G800EH

Brands by name

Popular brands