Playnation Redbrook Deluxe 381 Manual Download Page 83

Page: 83 / 142

FLUSH

STEP 35: ROOF SUPPORT ASSEMBLIES

1: LOCATE TWO 2 X 4 X 35.50" ROOF SUPPORT (LEFT), TWO 2 X 4 X 35.50" ROOF SUPPORT (RIGHT)

AND TWO 5/4 X 6 X 10.50" ROOF PEAK SUPPORT PIECES.
2: FIND A FLAT SURFACE TO WORK ON. LAY THE ROOF SUPPORTS DOWN ON THE FLAT SURFACE

WITH THE

COUNTER-SUNK HOLES FACING DOWN.

ALIGN THE ANGLED ENDS OF THE ROOF

SUPPORTS FLUSH WITH ONE ANOTHER. PLACE A ROOF PEAK SUPPORT ON TOP OF THE ROOF

SUPPORTS AS SHOWN. THE EDGES SHOULD BE FLUSH WHERE SHOWN BELOW.
3: USE FOUR #8 X 2" WOOD SCREWS TO ATTACH THE ROOF PEAK SUPPORT TO THE ROOF

SUPPORTS AS SHOWN BELOW.
4: MAKE ONE MORE ROOF SUPPORT ASSEMBLY BY REPEATING SUB-STEPS 2 AND 3.

2 X 4 X 35.5"

#8 X 2" WOOD SCREW

ROOF SUPPORT LEFT

2 X 4 X 35.5"

ROOF SUPPORT RIGHT

COUN

TER-SU

NK HO

LES FA

CES D

OWN

5/4 X 6 X 10.5"

ROOF PEAK SUPPORT

Summary of Contents for Redbrook Deluxe 381















































































































































Search results

Summary of Contents for Redbrook Deluxe 381

Reviews:

Related manuals for Redbrook Deluxe 381

Brands by name

Popular brands

Playnation Redbrook Deluxe 381, Manual

Search results

Summary of Contents for Redbrook Deluxe 381

Reviews:

Related manuals for Redbrook Deluxe 381

Brands by name

Popular brands