Playnation Redbrook Deluxe 381 Manual Download Page 106

Page: 106 / 142

CORNER POST

REMOVED FOR CLARITY

5/16" WASHER

UPPER LEVEL DECK SPACER

(CONNECTOR STEPS)

2 X 4 X 47.375" PANEL / DECK SUPPORT

5/16" X 3-1/2" LAG SCREW

LOWER LEVEL DECK

SUPPORT

UPPER LEVEL DE

NOTE: SOME COMPONENTS WERE

CORNER POST

CONNECTOR

FLUSH

3-3/8" BETWEEN STEPS

STEP 57A: CONNECTOR STEPS

1: TO MAKE THE CONNECTOR STEPS YOU WILL NEED TO FIND TWO 2 X 4 X 47.375" PANEL /

DECK SUPPORTS.
2: PLACE ONE PANEL SUPPORT (CONNECTOR STEP) AGAINST THE CORNER POSTS AND FLUSH

TO THE TOP FACE OF THE UPPER LEVEL DECK SPACERS. FASTEN USING 5/16" X 3-1/2" LAG

SCREWS AND 5/16" WASHERS THROUGH EACH ONE OF THE COUNTERSUNK HOLES.
3: PLACE THE SECOND PANEL SUPPORT (STEP) AGAINST THE CORNER POSTS BELOW THE FIRST

PANEL SUPPORT (CONNECTOR STEP). MEASURE 3-3/8" BETWEEN THE TOP STEP AND THE

BOTTOM STEP AND FASTEN USING 5/16" X 3-1/2" LAG SCREWS AND 5/16" WASHERS THROUGH

EACH ONE OF THE COUNTERSUNK HOLES.

Summary of Contents for Redbrook Deluxe 381















































































































































Search results

Summary of Contents for Redbrook Deluxe 381

Reviews:

Related manuals for Redbrook Deluxe 381

Brands by name

Popular brands

Playnation Redbrook Deluxe 381, Manual

Search results

Summary of Contents for Redbrook Deluxe 381

Reviews:

Related manuals for Redbrook Deluxe 381

Brands by name

Popular brands