Playnation Redbrook Deluxe 381 Manual Download Page 92 | Manualshive

Page: 92 / 142

background image

STEP 44: CONNECTOR SUPPORTS

1: THE 4 X 4 X 70" CONNECTOR SUPPORTS HAVE 3 COUNTER SUNK HOLES, TWO AT THE FRONT

AND ONE AT THE BACK. INSTALL THE CONNECTOR SUPPORTS SO THAT TWO OF THE COUNTER

SUNK HOLES FACE OUT AND THE COUNTER SUNK HOLE ON THE OPPOSITE SIDE FACE IN.
2: PLACE THE CONNECTOR SUPPORTS AGAINST THE CORNER POSTS AT THE REAR OF THE PLAY

SET. ONE WILL BE MOUNTED AT THE TOP END OF THE CONNECTOR LAG POSTS AND THE OTHER

ONE WILL BE MOUNTED AT THE BOTTOM END OF THE SAME CONNECTOR LAG POSTS.
3: MAKE SURE THE LEFT END OF THE CONNECTOR SUPPORTS ARE FLUSH TO THE SIDE OF THE

PLAYSET AND TIGHT AGAINST THE CORNER POSTS AND CONNECTOR LAG POSTS. FASTEN THE

CONNECTOR SUPPORTS USING 3/8" X 5" LAGS AND 3/8" WASHERS.

LAG POSTS

CONNECTOR

3/8" X 5" LAG

4 X 4 X 70" CONNECTOR SUPPORT

3/8" WASHER

4 X 4 X 70" CONNECTOR SUPPORT

COUNTER SUNK

HOLE FACES IN

COUNTER SUNK HOLES FACEOUT

82

«
...
90
91
92
93
94
...
»

Summary of Contents for Redbrook Deluxe 381















































































































































Reviews:

No comments

Related manuals for Redbrook Deluxe 381

Brand: Eclipse Combustion Pages: 46

Brand: DB Industries Pages: 60

Brand: Salsbury Industries Pages: 4

Brand: natus Pages: 149

Brand: Landoll Pages: 144

Brand: Castellini Pages: 299

GrainLogix XLB10

Brand: LOFTNESS Pages: 104

Brand: B-Safety Pages: 2

Brand: Veeder-Root Pages: 58

Brand: Qdot Pages: 6

Orux 480 Z Profile

Brand: Gamma Pages: 23

Brand: Baldan Pages: 68

Brand: Kett Pages: 40

Brand: H&S Pages: 30

Brand: Becen Pages: 5

THERMAPREP PLUS

Brand: Dentsply Maillefer Pages: 24

Brand: Rico Pages: 24

Brand: PCE Health and Fitness Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands