Playnation Redbrook Deluxe 381 Manual Download Page 127

Page: 127 / 142

#14 X 2" PAN HEAD SCREW

CORNER POST

1/4" FENDER WASHER

GROUND STAKE

DETAIL B

WASHER

SCREW

1/4" FENDER

SWING LEG

#14 X 2"

PAN HEAD

GROUND STAKE

DETAIL A

1: PLACE THE GROUND STAKES ON THE OUTSIDE OF THE SWING LEGS AS SHOWN BELOW.
2: HAMMER A GROUND STAKE INTO THE EARTH NEXT TO EACH SWING LEG AT AN ANGLE. DO

NOT HOLD THE UPPER PORTION OF THE STAKE

FTER THE FIRST COUPLE OF HITS OR IT MAY

VIBRATE HARSHLY AGAINST YOUR HAND. IF THE TOP PART OF THE STAKE TWISTS WHEN IT

ENCOUNTERS A ROCK OR ROOT YOU MAY HAVE TO BEND THE TOP PORTION OF THE STAKE

AGAINST THE SWING LEG. FINALLY INSTALL THE SCREW AND WASHER.
3: ATTACH EACH GROUND STAKE TO THE SWING LEG WITH A #14 X 2" PAN HEAD SCREW AND A

1/4" FENDER WASHER PROVIDED WITH THE GROUND STAKE.
4: TWO MORE GROUND STAKES WILL BE ON THE INSIDE OF THE SANDBOX ON THE TWO CORNER

POSTS CLOSEST TO THE ROCK WALL. ON THE INSIDE OF THE BASE OF THE PLAY SET DRIVE THE

GROUND STAKES INTO THE GROUND TO A DISTANCE THAT WILL NOT INTERFERE WITH THE HEX

BOLTS THAT ARE INSTALLED IN THE SANDBOX BOARDS. ATTACH EACH GROUND STAKE WITH A

#14 X 2" PAN HEAD SCREW AND A 1/4" FENDER WASHER PROVIDED WITH THE GROUND STAKE.

STEP 78: GROUND STAKES

117

Summary of Contents for Redbrook Deluxe 381















































































































































Search results

Summary of Contents for Redbrook Deluxe 381

Reviews:

Related manuals for Redbrook Deluxe 381

Brands by name

Popular brands

Playnation Redbrook Deluxe 381, Manual

Search results

Summary of Contents for Redbrook Deluxe 381

Reviews:

Related manuals for Redbrook Deluxe 381

Brands by name

Popular brands