Playnation Redbrook Deluxe 381 Manual Download Page 118

Page: 118 / 142

STEP 69: TELESCOPE

1: USE THE 1-1/4" WOOD SCREWS PROVIDED WITH THE TELESCOPE TO FASTEN ONE OF THE

HALF-CIRCLE SHAPED TELESCOPE BRACKETS ON TOP OF THE CONNECTOR SUPPORT AS SHOWN

IN THE DIAGRAM BELOW.
2: PLACET THE TELESCOPE STAND AND TELESCOPE INTO THE SLOT OF THE TELESCOPE BRACKET.
3: FASTEN THE REMAINING HALF-CIRCLE SHAPED TELESCOPE BRACKET TO THE OPPOSITE SIDE

THAT THE FIRST TELESCOPE BRACKET WAS INSTALLED. USE THE 1-1/4" WOOD SCREWS PROVIDED

WITH THE TELESCOPE TO ATTACH THE TELESCOPE BRACKET.

TELESCOPE

PROVIDED WITH TELESCOPE

SCALE 1 : 4

DETAIL B

1-1/4" WOOD SCREWS

HALF CIRCLE TELESCOPE BRACKET

CONNECTOR SUPPORT

108

Summary of Contents for Redbrook Deluxe 381















































































































































Search results

Summary of Contents for Redbrook Deluxe 381

Reviews:

Related manuals for Redbrook Deluxe 381

Brands by name

Popular brands

Playnation Redbrook Deluxe 381, Manual

Search results

Summary of Contents for Redbrook Deluxe 381

Reviews:

Related manuals for Redbrook Deluxe 381

Brands by name

Popular brands