Playnation Redbrook Deluxe 381 Manual Download Page 125

Page: 125 / 142

TOP PANEL BOARD

ROCK WALL SIDE

TIE A KNOT BEHIND

THIS HOLE IN THE

YOU MAY TIE

TWO KNOTS

IN THE ROPE

TO AID IN

CLIMBING IF

YOU WISH.

STEP 76: CLIMBING ROPE

1: THREAD ONE END OF THE ROPE THROUGH THE HOLE IN THE ROCK WALL SIDE TOP PANEL

BOARD.
2: TIE A SECURE KNOT ON THE INSIDE OF THE ROCK WALL SIDE TOP PANEL BOARD.
3: THREAD THE OTHER END OF THE ROPE THROUGH THE HOLE IN THE BOTTOM ROCK WALL

BOARD. PULL THE ROPE TIGHT AND TIE A SECURE KNOT BEHIND THE BOTTOM ROCK WALL

BOARD.
4: NOTE: YOU MAY TIE TWO KNOTS IN THE ROPE TO AID IN CLIMBING IF YOU WISH. DO THIS

BEFORE PERFORMING SUB STEP 3.
5: ONCE THE ROPE IS TIED ON BOTH ENDS ATTEMPT TO WRAP THE ROPE AROUND YOUR

HANDS. IF THE ROPE WRAPS AROUND YOUR HAND IT IS TOO LOOSE. UNT

E ONE END AND RETIE

THE ROPE UNTIL YOU CAN NO LONGER WRA

IT AROUND YOUR HAND.

115

Summary of Contents for Redbrook Deluxe 381















































































































































Search results

Summary of Contents for Redbrook Deluxe 381

Reviews:

Related manuals for Redbrook Deluxe 381

Brands by name

Popular brands

Playnation Redbrook Deluxe 381, Manual

Search results

Summary of Contents for Redbrook Deluxe 381

Reviews:

Related manuals for Redbrook Deluxe 381

Brands by name

Popular brands