Playnation Redbrook Deluxe 381 Manual Download Page 116

Page: 116 / 142

UPPER LEVEL STRINGER

BOLT CAP

3/8" LOCK NUT

3/8" WASHER

3/8" X 3-1/2" CARRIAGE BOLT

IRON DUCTILE SWING HANGER

TORQUE WASHER

UPPER LEVEL DECK

NOTE: SOME COMPONENTS WERE
REMOVED FOR CLARITY

STEP 67: PUNCHING BALL IRON DUCTILE

1: LOCATE THE IRON DUCTILE SWING HANGER. YOU ARE GOING TO USE THE IRON DUCTILE AS

A TEMPLATE IN THIS STEP TO DRILL HOLES THROUGH TWO DECK BOARDS.
2: DRILL TWO HOLES WITH A 3/8" DIAMETER DRILL BIT THROUGH THE IRON DUCTILE INTO THE

DECK BOARDS.
3: PLACE A 3/8" X 3-1/2" CARRIAGE BOLT THROUGH A TORQUE WASHER. PLACE THE CARRIAGE

BOLT INTO A 3/8" HOLE IN THE TOP OF THE DECK. HAMMER THE CARRIAGE BOLT HEAD TO SET

THE TORQUE WASHER TEETH INTO THE DECK BOARDS. REPEAT THIS PROCESS FOR THE OTHER

HOLE YOU DRILLED IN THE DECK.
4: PLACE THE IRON DUCTILE SWING HANGER OVER THE END OF THE CARRIAGE BOLTS. SECURE

THE SWING HANGER TO THE CARRIAGE BOLTS WITH 3/8" LOCK NUTS AND 3/8" WASHERS. PLACE

BOLT CAPS OVER ANY EXPOSED THREADS.

106

Summary of Contents for Redbrook Deluxe 381















































































































































Search results

Summary of Contents for Redbrook Deluxe 381

Reviews:

Related manuals for Redbrook Deluxe 381

Brands by name

Popular brands

Playnation Redbrook Deluxe 381, Manual

Search results

Summary of Contents for Redbrook Deluxe 381

Reviews:

Related manuals for Redbrook Deluxe 381

Brands by name

Popular brands