Planet MAP-3100 Software Manual Download Page 114

Page: 114 / 124

PLANET Mesh Network Manager Guide

5) Certificate

Password

•

The password for the HTTP certificate

•

Data type: Display String, default value is “httpconf”

6) Enable Access Control

•

A checkbox to enable or disable the access control of the HTTP daemon.

Parameters (HTTPD Access Table)

1) Device

•

The name of the device allowed for access control

•

Data type: Octet String

2) Subnet

•

The subnet allowed for access control

•

Data type: IP Address

3) Netmask

•

The netmask for the Subnet IP above

•

Data type: IP Address

4) Using

•

Define the type of access control to use through, either Device or Subnet

5) Comment

•

An optional comment regarding the table entry

•

Data type: Display String

6) Active

•

Define the status of the table entry, either active or inactive

PLANET Mesh Network Manager Guide

Page114 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands